Synthesis and Electrical Transport Properties of CuInGaTe2
Received Date: Apr 11, 2018 / Accepted Date: Apr 18, 2018 / Published Date: Apr 25, 2018
Copper Indium Gallium di-telluride (CIGT) single crystals were synthesized by a special modified Bridgman technique for crystal growth. Our XRD patterns clearly exhibited single phase. The temperature dependence of the electrical conductivity σ(T), Hall coefficient RH(T) in CuInGaTe2 single crystals have been demonstrated over the temperature range 143-558 K for the first time. The Hall coefficient sign confirms the samples displays the p-type conducting. The temperature dependence of the conductivity, Hall coefficient, Hall mobility, and charge carriers concentration were investigated were presented with a clear and effective pictures. CuInGaTe2 single crystals revealed electrical band gaps (or "transport gaps") ranging from 0.64 eV to 0.85 eV. The results obtained from electrical conductivity and carrier concentration revealed the sample p-type with acceptor energy level equal to ≈ 0.027 eV. From the obtained experimental data, the main fundamental physical constants and others for crystals under consideration have been estimated.
Keywords: Single crystals; Electrical conductivity; Cu–III–VI2 Chalcopyrite semiconductors
I–III–VI2 type chalcopyrite semiconductors where the group I element is Cu are feasible candidates for application as photo detectors , photo-voltaic cells  and light-emitting diodes . CuInTe2 and CuGaTe2 ternary compounds are direct band gap semiconductors crystallizing in the chalcopyrite structure. Their band gaps are Eg=0.96 eV (CuInTe2) and Eg=1.35 eV (CuGaTe2) . These values are well adapted to the solar spectrum and talking into consideration the high absorption coefficients of these materials they are very attractive for applications such as solar cells and optoelectronic device. Meanwhile to the best of our knowledge there have only been a few published reports on thin films of the quaternary compounds CuGaInTe2.
CuInGaTe2 films deposited for the first time at room temperature by using pulse electrode position method at a constant potential of – 0.75 V (SCE). The films exhibit one phase with optical band gap of range 0.9-1.5 eV for different work cycle . The dependence of the optical, structural and morphological properties were studied of CuIn0.7Ga0.3(Se1−xTex)2 thin films for two different compositions (for x=0.2 and 0.8). The films exhibit high absorption coefficient when evaporated by the electron-beam method on soda lime glass substrates. The optical energy gaps calculated to be 1.17 eV to 1.06 eV for x=0 at highest annealing temperature at 525°C and 1.12 eV to 1.02 eV for x=0.8 and at highest annealed temperature at 600°C. I-III-VI, compounds have great interest semiconducting material which have energy gap lies between 0.9 and 3.5 eV, and also many possibilities so I-III-VI, compounds used for electro-optical devices . In spite of all this, literature still lacks work that focuses explicitly on Hall properties, extrinsic carrier density, the impurity level, mobility of charge carriers, and in addition, relaxation time, diffusion coefficient, diffusion length, and the dominant scattering mechanisms that limit the mobility of a semiconductor in CuInGaTe2 crystals. In this work, a special modified Bridgman technique crystal growth technique was employed for the first time to produce single crystals of CuInGaTe2 (CIGT) and study the method of determination of semiconductor parameters based on the measurements of the conductivity and Hall effect.
Crystal growth and sample preparation
Bulk CuInGaTe2 was prepared by the melt growth technique based on Bridgman method . The constituent elements of Cu, In, Ga, and Te of high purity (6N) were weighted according to their stoichiometric molar ratio and sealed in evacuated silica tube (10-5 torr) and heated in a three zone tube furnace. The silica ampoule was internally coated with thin layer of carbon to prevent contamination of charge. The temperature of the furnace was raised gradually and kept constant for 12 h at 1100 K in the upper zone of the furnace at which the entire contents were completely melted. The lower portion of the growth tube was necked into a 2 mm diameter in order to promote the growth of single crystals. The ampoule was dragged slowly from the high temperature zone to the low temperature zone with a rate 2 mm/h. the ampoule was agitated to be mixing. As the ampoule drag into the low temperature zone, crystallization proceeds until the contents solidify. In the middle zone of the furnace the temperature was corresponds to the crystallization temperature of the compound. The ampoule drag into the third zone of the furnace slowly to cooled down, and then the furnace was switched off. The experimental equipment details for crystal growth are described elsewhere . Crystal perfection was checked by means of XRD to ensure the presence of the crystalline phase with high quality in the prepared ingot. After finishing the growth, the samples prepared polishing and washing have good optical quality surfaces.
Specimens of CuInGaTe2 with plane-parallel mirror surfaces were prepared from a large ingot. For studying the electrical conductivity and Hall effect, the sample was prepared in a rectangular shape with dimension 7.5 x 3 x 1 mm3. The sample had a length is more than three times its width. This aspect ratio is useful to a void a Hall voltage drop. The correction of the measured Hall voltage according to calculated correction factors  was applied. Silver paste was used for the ohmic contact. Measurement of the current voltage characteristics showed that the contacts were ohmic.
A compensation method used to measure the electrical conductivity and Hall effect measurements in a special cryostat  with a conventional D.C type potentiometer (type UJ33E mark) in a magnetic field of 6000 G which supplied from GMW electromagnet model 5403. During the investigation the temperature was varied 143-558 K and the sample was placed in Pyrex cryostat under vacuum 10-3 torr. The special cryostat used for low and high temperature measurements. Details of the experiments procedures and apparatus have been published .
Results and Discussion
Structural properties of CuInGaTe2 single crystals
Figure 1 depicts the X-ray diffraction and powder X-ray diffraction measurements of the CuInGaTe2 single crystal. All the major reflections are indexed as (hkl) peaks of CuInGaTe2 phase. The XRD patterns of CuInGaTe2 are well consistent with the literature data, so it can be said that the pure compounds with no impurities could be obtained.
Figure 2 shows the observed values of electrical conductivity σ is plotted against the inverse of temperature for CuInGaTe2 single crystal over a wide temperature range extending from 143 K to 558 K. At low temperature the electrical conductivity is low and increased with the rise of temperature, i.e., the temperature coefficient of resistance is negative and this is a characteristic of a semiconductor [12-14]. To understand the conductivity mechanism in CuInGaTe2, the conductivity curve shown is divided into three regions, the curve shows the typical semiconductor behavior. A typical semiconductor behavior curve consists of three major parts, below the transition, the transition region, and above the transition. For these regions, the electrical conductivity of CuInGaTe2 can is analyzed by the Arrhenius equation which relates the electrical conductivity and the temperature :
σ=σoexp (–ΔEg /2kBT) (1)
Where σ0 is the pre-exponential factor and is the ideal conductivity of monocrystalline structure and ΔEg is the energy gap for the conductivity. The energy gap width ΔEg could be calculated. It was found to be 0.85 eV. The value of energy gap is consistent with the results of CuIn0.7Ga0.3(Se1−xTex)2 thin films for two different compositions (for x=0.2 and 0.8) , so that CuInGaTe2 single crystals can be potential candidates as absorbers in photovoltaic applications. The roomtemperature electrical conductivity of a semiconductor specimen is equal to (0.35 Ω-1m-1).
The factor of (½) in the exponent appears with intrinsic semiconductors due to the possibility of distributions of electrons in the conduction band are independent of the distributions of holes in the valence band. By assuming that the carrier mobility varies rather slowly with temperature, eqn. (1) becomes:
σ=σo exp (–ΔEa/kBT) (2)
Where ΔEa refer to the activation energy. This energy is important factor for organic semiconductors studing .
The first activation energy (ΔEa1) occurs at low temperature while the second is at high temperature [16,17]. The second activation energy (ΔEa2) which occurred at high temperatures by the charge transfer is due to the thermal excitation of the carriers at the grain boundaries .
ΔEa1 value (in temperature range 143 K–193 K) was calculated from the slope of best fit straight line of Figure 2, from this region the ionization energy was calculated, indicating that the acceptor level lies 0.041eVabove the top of the valance band. The ΔEa2 value (in temperature range 193 K–313 K) was calculated from the slope of the Arrhenius plot as shown in Figure 2 and is 0.34 eV. There are two slopes indicate two conduction mechanisms are possible, observed two-stage temperature dependence of conductance (σ).
An intermediate region of the σ–T curve has been identified in temperature range 321 K–511 K, in which the carrier concentration is not actually constant, and in the third region, σ rises again. In the intermediate region where the carrier density (NA–ND=constant), until the intrinsic region is reached.
Since Hall measurements are an important tool to characterize the materials especially semiconductors, Hall coefficient (RH) have been measured on CuInGaTe2 single crystals. Samples were investigated in the same temperature range along a direction perpendicular to the C-axis which shown in Figure 3. RH was calculated from Hall voltage. The results showing p-type conduction indicate that the majority carriers are holes. The room temperature value of RH obtained by d.c. Hall coefficient measurements, is positive and equal to 87 x 10-4 m3/C. Hall coefficient (RH) directly determines the density of charge carriers in a given sample. Compute the concentration of charge carriers P=1/e RH and carrier concentration at room temperature are 7.18 x 1020 m-3.
Determination of the energy gap and ionization energy from Hall data is possible by plotting the relation between RH T3/2 and 103/T as shown in Figure 4. According to the relation:
RH T3/2=c exp (– ΔEg/2 kBT) (3)
By using the data presented in Figure 4, we can determine the band gap energy. It was found to be 0.71 eV. The depth of the impurity level was also computed and it was found to be 0.019 eV. These values closed to those obtained from the temperature dependence of electrical conductivity.
The relation of the conductivity and free carriers mobility as follows, σ=μen. The presented simultaneous measurements of the electrical conductivity and Hall effect will allow to systematically investigate the influence of temperature on the Hall mobility. Values of the temperature dependence of the natural logarithm of Hall mobility Lnμ plotted against LnT in Figure 5, the result is a straight line.
The slope of this straight line plot is then used to calculate the exponent. From the curve (5), we can demonstrate the presence of two different kinds modes on mobility variation around the transition temperature i.e., 248 K. At low temperature range T<248 K the mobility behavior increases with the increase of temperature obeying the lawμα T1.65, it seems that the value of the exponent n in the relation μ α Tn is in good agreement with the 1.5 value predicted by theory with those obtained for impurity and lattice scattering in other semiconductors.In the high temperature rangeT>248 K the mobility decreases according to the law μα T-3.65. This usually assumed that contribution to thermal conductivity by phonon-electron scattering is dominated. The room temperature value of the mobility equals 285 m2/Vs.
Compute the concentration of charge carriers, p=1/eRH. The temperature dependence of the carrier concentration is illustrated in Figure 6. At thermal equilibrium the formula:
Pi=c exp (– ΔEg/2 kBT) (4)
Thus the energy gap (ΔEg) can be calculated from the slope of the curve in the intrinsicregion, the energy gap is equal 0.64 eV, whichis in accordance with that obtained from the conductivity and Hall effect measurements.The presence of an ionized acceptor level at 0.019 eV above the top of the valence band obtained is in accordance with that obtained from the conductivity measurements. At room temperature the concentration can be estimated to be 7 x 1020 m-3. By using the assumption that the effective mass for holes is equivalent to the rest mass, the diffusion coefficient of holes can be calculated from the equation:
The value of diffusion coefficient at room temperature estimated to be 7.37 m2S-1. The mean free time of holes computed to be 4.2 x 10-15 sec at room temperature from the following equation . The diffusion length of holes (LP) in CuInGaTe2 specimen at room temperature was estimated as 1.76 x 10-7 m.
CuInGaTe2 was prepared in single crystal form by Bridgman technique. XRD was used to identify the crystalline nature of the compound. D.C electrical conductivity and Hall Effect measurement were carried out in a wide range of temperature (143-558 K). The measurement revealed that the compound P-type conductivity with energy gap ranging from (0.64-0.85 eV). Important parameter such as conductivity, hole concentration, Hall mobility, diffusion coefficient, diffusion length and relaxation time at room temperature were estimated.
- Devaney WE, Mickelson RA, Chen WS (1985) The conference record of the eighteenth IEEE Photovoltaic Specialists Conference—1985: Las Vegas, Nevada. New York: Institute of Electrical and Electronics Engineers.
- Loferski J, Sewchun J, Roesler B, Beaulieu R, Plekoszeski J, et al. (1978) Chapman in: Proceedings of the 13th IEEE Photovoltaic Spec. Conference, pp: 190.
- Kazmerski LL, Hallerdt M, Ireland PJ, Mickelson RA, Chen WS, (1983) J Vac Sci Technol, A1: pp: 395.
- Heinz A, Ossenbrink, Helm P, Ehmann H (1997) Proceedings of the 14th European Photovoltaic Solar Energy Conference, Barcelona, Spain, pp: 2161.
- Vinothini C 2015 ISSN (Print): 2279-0047 ISSN (Online): 2279-0055. IJETCAS 15-751.
- Shay JL, Wernik JH, (1975) Ternary Chalcopyrite Semiconductors: Growth, Electrical Properties and Applications, Pergamon, NewYork.
- Gamal GA, Nassary MM, Hussein SA, Nagat AT (1992) Single Crystal Growth and Electrical Properties of Gallium Monotelluride. Cryst Res Technol 27: 629-635.
- Hussein SA, Nagat AT (1989) On the preparation and electrical properties of Thallium selenide monocrystals. Cryst Res Technol 24: 283-289.
- Runyan WR (1975) Semiconductor measurements and instrumentation. McGRAW-HILL Book company.
- Nagat AT (1989) Investigation of the electrical properties of Thallium monsulphide single crystal. J Phys Condens. Matter 1: 7821-7825.
- Nagat AT, Hussein SA, Gameel YH, Belal AA (1990) Anisotropy of electrical conductivity and Hall effect in gallium selenide crystals. Indian J Pure Ap Phy 28: 586-589.
- Omar MA (1975) Elementary Solid State Physics, (2nd edn.), John Wiley and Sons Inc, New York.
- Okamoto Y, Brenner W (1964) Organic Semiconductors. Chapman and Hall Ltd, London.
- Mille M (1966) The Structure of Polymers. Reinhold Publishing Corporation, New York.
- Blakemore JS (1974) Solid State Physics. (2nd edn.), by W.B. Saunders Company.
- Orton J, Cold Smith BJ, Chapman JA, Powell MJ (1982) The mechanism of photoconductivity in polycrystalline cadmium sulphide layers J Appl Phys 53: 1602.
- Nicodemo L, Nicolais L, Romeo G, Scafora E (1978) Temperature effect on the electrical resistivity of metal/polymer composites. Polym Eng Sci, Academic Press, New York.
Citation: Salem A, Salwa AS, Hussein SA, Ezzeldien M (2018) Synthesis and Electrical Transport Properties of CuInGaTe2. J Laser Opt Photonics 5: 183. DOI: 10.4172/2469-410X.1000183
Copyright: © 2018 Salem A, et al. This is an open-access article distributed under the terms of the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original author and source are credited.
Select your language of interest to view the total content in your interested language
Share This Article
- Total views: 3367
- [From(publication date): 0-2018 - Sep 22, 2019]
- Breakdown by view type
- HTML page views: 3286
- PDF downloads: 81